[PDF&VCE] Pass 200-355 Exam By Exercising Lead2pass Latest 200-355 VCE And PDF Dumps (171-180)
2016 September Cisco Official New Released 200-355 Dumps in Lead2pass.com!
100% Free Download! 100% Pass Guaranteed!
After purchasing the dumps for the 200-355 Exam from Lead2pass, I had no doubt that I’d easily pass the exam. Bundle of thanks to Lead2pass for helping me pass the exam without any troubles.
Following questions and answers are all new published by Cisco Official Exam Center: http://www.lead2pass.com/200-355.html
QUESTION 171
Drag and Drop Questions
Answer: 
QUESTION 172
Lab Simulation 
All equipment is operational. Through which two methods can a wireless client receive an IP address when associating to the WLAN? (Choose two.)
A. The clients can receive an IP address from SW1.
B. Tie clients can receive an IP address from WLC1.
C. The clients will not receive an IP address from either DHCP server because of overlapping address ranges.
D. The clients can receive an IP address in a round-robin maner from either SW1 or WLC1.
E. The clients can use a static IP address.
Answer: BE
Explanation:
As shown be,ow, the DHCP server functionality has been enabled on the WLC1. Aside from DHCP, all clients can always statically assign themselves an IP address.
QUESTION 173
Lab Simulation 
In setting up the wireless network, it is desired that the DHCP server that is configured in WLC1 provides IP addressing to the WLAN. When devices attempt to join the network, they fail to receive an IP address in the range provided by the DHCP server in WLC1, but they do receive an IP address from the DHCP server in SW1. What is causing this issue?
A. The external DHCP server in SW1 will always be the preferred DHCP server and WLC1 will always be the secondary DHCP server in the WLAN.
B. The DHCP server address for SW1 needs to be removed from the DHCP server configuration in WLC1.
C. The primary DHCP server address in WLC1 is incorrect.
D. The primary DHCP server configured in WLC1 is not enabled.
Answer: D
Explanation:
This can be verified by the following screen shot, showing the DHCP server is disabled at the bottom:
QUESTION 174
Lab Simulation 
Which change can correct inband access to the WLC?
A. change the switch FastEthernetO/1 duplex setting
B. change the switch FastEthernetO/1 speed setting
C. enable the switch FastEthernetO/1 spanning-tree port-fast trunk
D. change the switch FastEthernetO/1 trunk encapsulation
E. change the WLC management interface to use DHCP
F. change the WLC management interface VLAN
G. change the WLC configuration of NTP
H. browse to WLC via http://10.10.10.10
Answer: D
Explanation:
All of the other ports in the network are using the default VLAN (VLAN 1) but port 0/1, which connects to the WLC, is configured as a trunk, so VLAN 1 is not operationsl.
QUESTION 175
Lab Simulation 
When a client associates to ExamSSlD, which network address will be assigned?
A. The IP address assigned will be based on the AP network assignment of 10.10.10.0.
B. The IP address assigned will be based on the AP network assignment of 172.16.23.0.
C. The IP address will be assigned in a round-robin format based on the 172.16.12.0, 172.16.23.0,192.168.14.0 address pools.
D. The IP address will be assigned in a round-robin format based on the 172.16.12.0, 192.168.14.0,192.168.25.0 pools.
E. The IP address will be assigned in a round-robin format based on the 172.16.12.0, 172.16.23.0,192.168.14.0,192.168.25.0 pools.
Answer: D
Explanation:
The IP addresses will be assigned round robin to the three interface groups, which we can see are vlan20, vlan40, and vlan50. From the WLC-interfaces tab we see that the IP addresses assigned to these 3 interfaces are 172.16.12.10, 172.16.14.10, and 192.168.25.10, respectively.
QUESTION 176
Lab Simulation
The AP is unable to join the WLC. What switch configuration will correct this problem?
A. interface vlanl
ip helper-address 10.10.10.10
B. interface vlan20
ip helper-address 10.10.10.10
C. ipdhcp pool vlanl
option 43 ascii ‘10.10.10.10’
D. ip dhcp pool vlan20
option 43 ascii ‘10.10.10.10’
E. ipdhcp pool vlanl
option 43 hex f1040a0a0a0a
F. ip dhcp pool vlan20
option 43 hex f1040a0a0a0a
Answer: F
Explanation:
Keep the following in mind when troubleshooting wireless DHCP issues:
Option 43 is used to inform the DHCP client of the WLC AP-management IP address.
Use the ip dhcp pool command for VLAN 20 and enter the AP-management IP address as part of option 43.
The command format is option 43, followed by the correct IP address in hexadecimal format, as shown in the example.
If there is only one WLC management address, the Length is 04 (hex), and in this case the WLC management IP address is 10.10.10.10, which is 0a0a0a0a (hex).
QUESTION 177
Lab Simulation 
Which four levels of messages will be sent to the logging server? (Choose four.)
A. alerts
B. critcal
C. debugging
D. emergencies
E. errors
F. informational
G. notifications
H. warnings
Answer: ABDE
Explanation:
There are a total of 8 logging severity levels. They are:
We can see from the output that the severity level was set to Critical, which means that all messages level 3 and less will be sent.
QUESTION 178
Lab Simulation 
What APTx Power Level Assignment would be required to increase power by 3 dBm on 2.4GHz radio?
A. 1
B. 2
C. 3
D. 4
E. 5
F. 6
G. 7
H. 8
Answer: D
Explanation:
From the output, we can see the current power level setting for the 802.11 bgn (2.4Ghz tab) is set at 5. Based on the following tyable from Cisco, that would mean the output power is 3 mW:
Here is the power conversion table to go from mW to 3bm:
So, with a power level setting of 5, the output power is is 3mW, or 5 dbm. A power level of 4 would increase it to 6mW, or 8 dbm.
QUESTION 179
Lab Simulation 
Tablets and other wireless clients are unable to connect at any 802.11 n data rates. What is the most likely cause of this problem?
A. WLAN > General properties are incorrectly configured.
B. WLAN > QoS properties are incorrectly configured.
C. WLAN > Security properties are incorrectly configured.
D. WLAN > Advanced properties are incorrectly configured.
E. Wireless > AP > 802.11 a/n is incorrectly configured.
F. Wireless > 802.11a/n > Network is incorrectly configured.
Answer: C
Explanation:
802.11n only supports open authentication or the use of WPAv2 with AES. From the output shown in this question, we can see that WPA/WPA2 using TKIP has been configured, not AES.
QUESTION 180
Lab Simulation 
Old 2.4-GHz wireless laptops are unable to connect. What is the most likely cause of this problem?
A. WLAN > General properties are incorrectly configured.
B. WLAN > QoS properties are incorrectly configured.
C. WLAN > Security properties are incorrectly configured.
D. WLAN > Advanced properties are incorrectly configured.
E. Wireless > AP > 802.11 b/g/n AP is incorrectly configured.
F. Wireless > AP > 802.11 b/g/n > Network is incorrectly configured.
Answer: F
Explanation:
Clienlink is not enabled and should be in a mixed client environment. Many networks still support a mix of 802.11a/g and 802.11n clients. Because 802.11a/g clients (legacy clients) operate at lower data rates, the older clients can reduce the capacity of the entire network. Cisco’s ClientLink technology can help solve problems related to adoption of 802.11n in mixed-client networks by ensuring that 802.11a/g clients operate at the best possible rates, especially when they are near cell boundaries.
I understood all of the questions very easily. I scored 96% on my first try. I am definitely going to spread the word amongst friends and colleagues. Keep up the great work.
200-355 new questions on Google Drive: https://drive.google.com/open?id=0B3Syig5i8gpDS2dtNHE0NWQwQzQ
2016 Cisco 200-355 exam dumps (All 410 Q&As) from Lead2pass:
http://www.lead2pass.com/200-355.html [100% Exam Pass Guaranteed]